silicone membrane, silicone blanket,
silicone rubber, silicone sheet,silicone foils
Peter Lin, cnc@cncGlass.com,
cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365
www.cncglass.com www.cnceva.com

Silicone rubber sheet for glass industry is a key component of our company dedicated to supporting the glass vacuum laminated furnace according to market demand.
Laminated glass vacuum furnace uses vacuum principle, make the glass heated under vacuum conditions, with the atmospheric pressure, let the glass in the vacuum bag pressed to exclude air and unable to make bubbles, vacuum bag is under heating and vacuum pumped conditions to make two or more pieces of glass and EVA hot together.
Vacuum bag is a core part of glass vacuum laminated furnace, it makes up of two pieces of silicone rubber sheet and silicone sealing edge, silicone rubber sheet is a key component of the entire laminated furnace, its quality directly affects the quality of glass products.

thermal cutter, hot price ,heating cutter,
heating knife, heating trimmer for eva pvb sgp lamination
Peter Lin, cnc@cncGlass.com,
cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365
www_cncGlass_com www_cncEVA_com

Differences between CNC02 and CNC01:

*CNC02-Continuously-Working Thermal Cutter is designed for continuously working with air cooling system, while CNC01-Intermittently-Working is only for short time working, you need to release the button intermittently for cooling after short time heating in case itself gets too hot.

*CNC02-Continuously-Working is able to trim the edges with minimum of smoke and no burned marks.

*CNC02-Continuously-Working is lighter ,only 610g, easier to handle, while CNC01 is 950g.

*CNC02-Continuously-Working is available for high point temperature adjustment, 16 sections of temp to set. So you don’t need to let the blades going up to 500C degrees each time you use it, you may only set the lower temperature(for example about 300C degrees) only if it’s high enough for you to trim interlayer remains, so you can prolong the life time of the blades, and save cost.

Peter Lin, cnc@cncGlass.com,
cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365
www_cncGlass_com www_cncEVA_com

Edges Cleaning hot knife for SGP PVB laminated safety glass
Hand operated tool for cutting small quantities, for short-time operation only.
To cut and seal synthetic fiber products, such as ropes, bands, belts and fabric.
Fitted with cutting foot, the combined tool is especially effective for cutting
synthetic fabric without cutting surface.
Controlling heating by switching the toll on and off

Peter Lin, cnc@cncGlass.com,
cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365

Hot Knife Electric Rope Cutter Cautions
Always operate the Hot Knife in well ventilated space.
Never burn off the excess residue on the Hot Knife blade. The blades will over heated and be warped.
Only operate Hot Knife when it is in contact with the insulation board
Keep hot blades away from skin, clothing and other flammable materials.
Allow blades to cool before handling. Hot Knife may cause injury or burns to exposed surfaces.
If the temperature inside the tool is too high, the unit will get hot and the internal thermal protectors will turn it off, after it cool, the Hot Knife will operate again.

thermal cutter, hot price ,heating cutter,
heating knife, heating trimmer for eva pvb sgp lamination
Peter Lin, cnc@cncGlass.com,
cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365
www_cncGlass_com www_cncEVA_com

Differences between CNC02 and CNC01:

*CNC02-Continuously-Working Thermal Cutter is designed for continuously working with air cooling system, while CNC01-Intermittently-Working is only for short time working, you need to release the button intermittently for cooling after short time heating in case itself gets too hot.

*CNC02-Continuously-Working is able to trim the edges with minimum of smoke and no burned marks.

*CNC02-Continuously-Working is lighter ,only 610g, easier to handle, while CNC01 is 950g.

*CNC02-Continuously-Working is available for high point temperature adjustment, 16 sections of temp to set. So you don’t need to let the blades going up to 500C degrees each time you use it, you may only set the lower temperature(for example about 300C degrees) only if it’s high enough for you to trim interlayer remains, so you can prolong the life time of the blades, and save cost.

Peter Lin, cnc@cncGlass.com,
cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365
www_cncGlass_com www_cncEVA_com

Edges Cleaning hot knife for SGP PVB laminated safety glass
Hand operated tool for cutting small quantities, for short-time operation only.
To cut and seal synthetic fiber products, such as ropes, bands, belts and fabric.
Fitted with cutting foot, the combined tool is especially effective for cutting
synthetic fabric without cutting surface.
Controlling heating by switching the toll on and off

Peter Lin, cnc@cncGlass.com,
cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365

Hot Knife Electric Rope Cutter Cautions
Always operate the Hot Knife in well ventilated space.
Never burn off the excess residue on the Hot Knife blade. The blades will over heated and be warped.
Only operate Hot Knife when it is in contact with the insulation board
Keep hot blades away from skin, clothing and other flammable materials.
Allow blades to cool before handling. Hot Knife may cause injury or burns to exposed surfaces.
If the temperature inside the tool is too high, the unit will get hot and the internal thermal protectors will turn it off, after it cool, the Hot Knife will operate again.

PTFE high-temperature net belt
Fiberglass fabric coated with PTFE is made up
of high-capability fiberglass which has steeped into PTFE.

Peter Lin, cnc@cncGlass.com, cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365

It is a new product with Main capability and characteristics:
1). It can be used under the temperature of -196°C to 300°C,
2) which has the capability of weather resistant and age
3)resistant. Under practical situation of high temperature of
4)250°C for 200 days, not only the intensity will not decrease,
5)the weight will not reduce; if put it under the high temperature
6) of 350 °C for 120 hours, the weight only decreased by about
7) 0.6%; under the situation of -180 °C, it will not chap and keep
8) the original pliability;

Green polyester tape is ideal for safety glazing edges masking and general powder coating applications; it is the industry standard for polyester tape.

Removes cleanly from surfaces without leaving a residue
Maximum Temperature: 500 degrees F
Total Thickness: 3.5 mils
This Polyester Tape has a silicone adhesive and is great for Powder Coating and can also be used for safety glazing edges masking, E-Coating, Plating and Anodizing. It can also be used for applications such as taping off large surfaces, general purpose die cutting, PC board masking.

Peter Lin, cnc@cncGlass.com,
cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365
www.cncglass.com www.cnceva.com